CNC New 3 axis TB6600 Stepper Motor Driver Board 4.5A/36V For Engraving Machine

• 100% brand new and high quality

• This document describes the basic functionality and the electrical specifications of StepperOnline's Three Axis TB6600 CNC Driver Board
• Supports MACH3, KCAM4, EMC2 etc …
• Can drive four channels 4.5A stepper motors, input voltage up to 18V - 40V.
• Resolution 1, 1/2, 1/4, 1/8, 1/16 micro stepping output.
• 100% Full DC-DC optical isolation to protect the user's computer and equipment.
• Four channels of 0.4 - 4.5A adjustable output current for 2/4 phase bipolar stepper driver.
• Build with 3 ways relay output and 5 ways limit interface
• Automatic idle-current reduction.
• Dimension:Approx.18.5cm x 11.2cm x3cm
• Quantity:1PC
                                                      Electrical Properties(ambient temperature Tj = 25C)
  　

  Input Voltage	12V-45VDC, Recommend DC24V or DC36V
  Output Current	Peak Current 5A/phase, 8 Options available
  Driving Mode	Constant current PWM Control
  Exciting Mode	1, 1/2, 1/4, 1/8, 1/16

  
  Current Setting
  

  Current	0.4A	1.6A	2.6A	3.2A	3.8A	4.0A	4.3A	4.5A
  S1	ON	OFF	ON	OFF	ON	OFF	ON	OFF
  S2	ON	ON	OFF	OFF	ON	ON	OFF	OFF
  S3	ON	ON	ON	ON	OFF	OFF	OFF	OFF

  Subdivision Setting
  　

  Subdivision	NC	1	1/2	1/2	1/4	1/8	1/16	NC
  S4	OFF	OFF	OFF	OFF	ON	ON	ON	ON
  S5	OFF	OFF	ON	ON	OFF	OFF	ON	ON
  S6	OFF	ON	OFF	ON	OFF	ON	OFF	ON

  Warning
  Make sure the power supply voltage dose not exceed the drive’s input range. Double check the connections and make sure the power lead polarity is correct.
  Do not set high current to small stepper motor. It is possible that the motor will be damaged.
  Disconnect the motor from the load if you are not sure the move direction. Adjust the axis in the middle before trying to run the motor.
  Never disconnect the motor lead when the power source is energized.

TB6560 3 Axis 3.5A CNC Engraving Machine Stepper Motor Driver Board Controller  small Brand new and high quality Suitable for processing various pattern mould, carving portrait, scenery, handwriting, sealing, etc. Great for advising, such as brand, architechture mould, badge, nameplate, display boards, doorplate, furniture decoration, etc. 4 changeable electric currents: 0.6A, 1.2A, 1.8A, 2.5A Support MACH2, MACH3, KCAM4 series software High accuracy, small vibration, low noise Stable performance, safe and easy to use

It can drive 3 stepper motors at the same time With the 4th axis expansion Spindle relay output, easy to use software such as mach3 to control spindle start and stop Semi-flow control to effectively stop the motor when the current is reduced to a minimum With fan interfaces With 3 way 0.8-3.5A (peak) rated output of two-phase adjustable-current bipolar stepper motor drive Standard parallel port interface Support MACH2,  KCAM4 series software With optical isolation and DCDC power supply isolation to protect your computer parallel port and equipment With limit switch (can connect 4 aixs limit switch) Support four microstepping --- 1, 1/2, 1/4, 1/16 24-36V single switching power supply, microchips to use as a 5V power supply, stable and small heat

++ Package included ++

1 x TB6560 3 axis stepper motor controller 1  x Cable

4A TB6600 Stepper Motor Driver Controller 9~42V TTL 16 Micro-Step CNC 

3D Printer Controller Board Module For RAMPS 1.4 REPRAP PRUSA MENDEL New

Brand new and high quality. RAMPS 1.4: RepRap Arduino Mega Pololu Shield 1.4 Fully assembled & tested It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack. Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases. As of version 1.3 in order to fit more stuff RAMPS is no longer designed for easy circuit home etching. If you want to etch your own PCB either get version 1.25 or Generation_7_Electronics. Version 1.25 and earlier are "1.5 layer" designed boards (i.e. it's double sided board, but one of layers can easily be replaced with wire-jumpers) that is printable on your RepRap with the etch resist pen method, or home fabbed with toner transfer. This board is mostly based on Adrian's Pololu_Electronics and work by Tonok. Copper etch resists methods suggested by Vik. Also inspired by Vik's work with EasyDrivers. circuit design based mostly on Adrian's Pololu_Electronics Joaz at RepRapSource.com supplied initial pin definitions and many design improvements. Much inspiration, suggestions, and ideas from Prusajr, Kliment, Maxbots, Rick, and many others in the RepRap community. Size: 11.5cm x 6cm / approx. 4.5in x 2.4in. Package: 1 x Printer Controller for RAMPS 1.4

CNC Router Single 1 Axis Controller Stepper Motor Drivers TB6560 3A driver board

CNC Router Single 1 Axis Controller Stepper Motor Drivers TB6560 3A driver board

100% brand new and high quality Size:75*50*35(mm)(LxWxH) / 2.95''x1.96''x1.37'' (approx) Rated maximum output: ± 3A, peak 3.5A. Working voltage DC 10V-35V. Recommended to use a switching power supply DC24V power supply. Using the Toshiba TB6560AHQ new original chip with low voltage shutdown, overheating stop and over current protection circuit to ensure optimal performance. For two-phase within 42,57 stepping 3A / four-phase / of line four / six-wire stepper motor, and is not suitable for more than 3A stepper motor. Automatic half current function. 6N137 high-speed optical coupling, guarantee high speed without losing step. Subdivision: whole step, half-step, step 1/8, 1/16 step, a maximum of 16 Subdivisions. Features similar products: 1 current grade-by-adjustable to meet your demand for a variety of applications. 2 semi-automatic flow adjustable. 3 6N137 high-speed optical coupling, guarantee high speed without losing step. 4 plate printed setup instructions operation without manual also. 5 thick teeth radiator, good heat dissipation.

 SG20 sealed ball tack roller Groove Ball U Groove Bearing 6*24*11mm

 

Size: 6*24*11mm
Inside diameter: 6mm
Outside Diameter: 24mm
Width: 11mm
Pakcage:1pcs

8mm GT2 20 teeth 6mm width timing pulley ultimaker reprap

Model Number:8mm GT2 20 teeth 6mm width timing pulley
Install Style:Plug-in
Frequency:High Frequency
Power:Medium Power
Type:Other
is_customized:Yes
Brand:Blue Road
Material:Aluminum
Inner diameter:8mm
Number of gears:20 teeth
Type:
ultimaker reprap printer
Range:3d printer accessories

Product Description

8mm GT2 20 teeth 6mm width timing pulley 3d printer accessories

Name : ultimaker reprap
3d printer GT2 synchronous gear
Material: Aluminum applicable : 6mm wide belt
Inner diameter : 8mm Gear : 20 tooth




Range : ultimaker reprap 3d printer GT2 belt

MKS TB6600

High performance, cost-effective. Automatic idle-current reduction. Supply voltage up to 45V DC Output current up to 4.5A. Can be used on ramps(need mks cd),mks gen and so on

• 

  MKS TB6600 board
 
• 

  MKS TB6600 Connect
 
• 

  MKS TB6600-Back

Features

• PWM chopper-type single-chip bipolar sinusoidal micro-step stepping motor driver.
• BiCD 0.13 (50 V) process, Lower Ron: 0.4 Ω(typ.).
• Output withstand voltage: VCC = 50 V.
• Output current: IOUT = 5.0 A (absolute maximum ratings, peak, within 100ms);IOUT = 4.5 A (operating range, maximal. value);More Stepper motors
• Thermal shut down (TSD) protection.
• Under voltage lock out (UVLO) protection.
• Over-current detection (ISD) protection.
• Double input port: Anti-reverse structure IDC haeder( 8pin symmetrical input) & HT-396-4pin input (suit for DIY).
• Stepless adjustable reference voltage.
• Compatible the CNC Stepper Motor.
• Offer an solution to change your CNC to 3D Printer.
• Board size: 50.5*50mm ; Carry 50*50*23mm aluminum Heat sink which build-in fix hole and connection hole.
• Auto half current, energy conservation.
• Photoelectric-isolation used in the input port,compatible more drive Level.
• Programmable micro step - 1/1, 1/2A, 1/2B, 1/4, 1/8, 1/16.
• Affordable price.

Settings of Driver

Connect direct

Connect with MKS CD