CNC New 3 axis TB6600 Stepper Motor Driver Board 4.5A/36V For Engraving Machine

• 100% brand new and high quality

• This document describes the basic functionality and the electrical specifications of StepperOnline's Three Axis TB6600 CNC Driver Board
• Supports MACH3, KCAM4, EMC2 etc …
• Can drive four channels 4.5A stepper motors, input voltage up to 18V - 40V.
• Resolution 1, 1/2, 1/4, 1/8, 1/16 micro stepping output.
• 100% Full DC-DC optical isolation to protect the user's computer and equipment.
• Four channels of 0.4 - 4.5A adjustable output current for 2/4 phase bipolar stepper driver.
• Build with 3 ways relay output and 5 ways limit interface
• Automatic idle-current reduction.
• Dimension:Approx.18.5cm x 11.2cm x3cm
• Quantity:1PC
                                                      Electrical Properties(ambient temperature Tj = 25C)
  　

  Input Voltage	12V-45VDC, Recommend DC24V or DC36V
  Output Current	Peak Current 5A/phase, 8 Options available
  Driving Mode	Constant current PWM Control
  Exciting Mode	1, 1/2, 1/4, 1/8, 1/16

  
  Current Setting
  

  Current	0.4A	1.6A	2.6A	3.2A	3.8A	4.0A	4.3A	4.5A
  S1	ON	OFF	ON	OFF	ON	OFF	ON	OFF
  S2	ON	ON	OFF	OFF	ON	ON	OFF	OFF
  S3	ON	ON	ON	ON	OFF	OFF	OFF	OFF

  Subdivision Setting
  　

  Subdivision	NC	1	1/2	1/2	1/4	1/8	1/16	NC
  S4	OFF	OFF	OFF	OFF	ON	ON	ON	ON
  S5	OFF	OFF	ON	ON	OFF	OFF	ON	ON
  S6	OFF	ON	OFF	ON	OFF	ON	OFF	ON

  Warning
  Make sure the power supply voltage dose not exceed the drive’s input range. Double check the connections and make sure the power lead polarity is correct.
  Do not set high current to small stepper motor. It is possible that the motor will be damaged.
  Disconnect the motor from the load if you are not sure the move direction. Adjust the axis in the middle before trying to run the motor.
  Never disconnect the motor lead when the power source is energized.

TB6560 3 Axis 3.5A CNC Engraving Machine Stepper Motor Driver Board Controller  small Brand new and high quality Suitable for processing various pattern mould, carving portrait, scenery, handwriting, sealing, etc. Great for advising, such as brand, architechture mould, badge, nameplate, display boards, doorplate, furniture decoration, etc. 4 changeable electric currents: 0.6A, 1.2A, 1.8A, 2.5A Support MACH2, MACH3, KCAM4 series software High accuracy, small vibration, low noise Stable performance, safe and easy to use

It can drive 3 stepper motors at the same time With the 4th axis expansion Spindle relay output, easy to use software such as mach3 to control spindle start and stop Semi-flow control to effectively stop the motor when the current is reduced to a minimum With fan interfaces With 3 way 0.8-3.5A (peak) rated output of two-phase adjustable-current bipolar stepper motor drive Standard parallel port interface Support MACH2,  KCAM4 series software With optical isolation and DCDC power supply isolation to protect your computer parallel port and equipment With limit switch (can connect 4 aixs limit switch) Support four microstepping --- 1, 1/2, 1/4, 1/16 24-36V single switching power supply, microchips to use as a 5V power supply, stable and small heat

++ Package included ++

1 x TB6560 3 axis stepper motor controller 1  x Cable

4A TB6600 Stepper Motor Driver Controller 9~42V TTL 16 Micro-Step CNC